What is improper maintenance period after discontinuation of the gas mapna boiler engineering and manufact heating hazards present, China's heating season has come to an end, many dedicated to heating gas boiler has entered the period of suspension. Many users believe that disabled the boiler tubes will not need to, as long as doing cleaning and inspection work on it at the time of shutdown. As the boiler in the boiler industry for many years of business - fast boiler tell you, if neglected maintenance of the boiler during the gas boiler disabled, it is easy to make the boiler anomalies occur at the next start. Corrosion is a serious hazard gas boiler run time, the danger goes without saying that a lot of companies use gas-fired boiler units attach great importance to the boiler corrosion protection measures, and achieved some success. It should be emphasized that not only corrosion occurs during operation of the gas central heating boiler, if not take appropriate protective measures during boiler outage, will enter the oxygen in the gas boiler wet metal surface corrosion, this corrosion caused by damage to the gas boiler, much more often than in the serious corrosion in boiler operation, therefore, must draw our attention. Gas central heating boiler deactivated after the release came out of water, the pot or the furnace very humid, coupled with insufficient ventilation, long time in a wet state. After a lot of air to enter all parts of the air involved are likely to produce oxygen corrosion, and erosion due to ulcer type and form of multi-spot-based corrosion, resulting in a lot of rust. This effect will be that the internal boiler corrosion metal wall thinning, reduced strength, shortening the life of the gas central heating boiler. Therefore, even if the heating season has ended, gas heating boiler stop running for maintenance of the boiler we should not be ignored. Correct method of operation are: boiler stoker boiler regularly to conduct a comprehensive inspection, once the abnormal situation immediately take appropriate maintenance measures. At the same time, but also to ensure good boiler room ventilation and dry environment.

You have to know the energy consumption of the mapna boiler engineering and manufact problem (to solve the problem of reheat steam temperature) to solve the problem of temperature reheat steam boiler measures 1 run 1.1AGC control measures to closely monitor fluctuations in the amount of coal, the fuel surge slashed appears when shall be conditioned for manual intervention by warm water. 1.2 artificially adjusting the load, increase or decrease the amount of coal can not be too large. 1.3 adjusted to optimize the combustion tests, the optimum value of oxygen boiler, the boiler properly regulate the amount of oxygen. 1.4 put into operation the burner adjustment mode, by adjusting a combustion temperature of the boiler reheat guaranteed. 1.5 Normal into the boiler reheat steam temperature control. 1.6 intense monitoring each stage reheater steam temperature, steam temperature adjustment for adjusting so that ground, the fine reduced spray desuperheater water, the control reheat steam temperature. 1.7 Test mastered by pulverizing system operation to change the influence of reheat steam temperature, analyze the causes and make predictable adjustments. 1.8 rational for sootblowing heating surface. 1.9 stratified fuel amount adjustment, reasonable control center of the flame, adjust a secondary air ratio, the excess air ratio changing, if necessary. 1.10 reheat section controls an amount of cold extraction. 1.11 administered with # 1, # 2 as soon as high pressure heater. 2 routine maintenance and testing 2.1 combustion adjustment experiment to determine the best mode of operation and control parameters boilers. 2.2 to detect and analyze the reasons offset the center of the furnace flame occurs, and take specific measures. 2.3 improve the quality of the reheat steam temperature control. 3 3.1 eliminate downtime desuperheating water leakage defects in the valves. 3.2 heating surface coking, fouling cleaning. 3.3 burner maintenance inspection, the swing angle position correction. 3.4 dredge preheater, treatment of flue leakage. 4 4.1 waterwall transformation, reheater, superheater tube cutting, check the internal corrosion and scaling conditions. 4.2 due to equipment problems reheat steam parameters less than the design value, or burner heating surface for transformation.

Automatic environmentally friendly gas mapna boiler engineering and manufact which also highlight the advantages of the nominally see, automatic environment-friendly gas boiler has two obvious advantages, automatic and clean environment. From the design point of view the structure of the boiler, because its upper portion an annular steam chamber a large capacity and advanced water separation measures, such long-term stability for the steam boilers, steam quality is very excellent. So, in addition to automatic and environmentally friendly, it also has no obvious advantage? First, the working reliability in order to fully protect the safe use of the boiler, gas boiler make automatic green technology upgrades, the use of more high-quality safety accessories, such as: excellent quality safety valve, globe valve and level electrode (automatic imported products) , pressure gauges and pressure controllers and other safety accessories, these accessories are so reliable operation of the boiler. Second, high thermal efficiency boilers automatic gas overpressure chain protection, when the pressure inside the boiler beyond the set value, and disables the heater alarm, but it also greatly improves the heat obedience, built especially smoke tube designed spoiler and enhanced convection heat transfer, heat obedience gas boiler boiler than the average increase, let the heat get plenty to show. Third, style decency professional gas boiler according to the company, the automatic environment-friendly than gas-fired boiler is equipped with a high-quality touch screen PLC control system, strong immunity, maintenance is also very convenient. And automatic gas boiler style decency, compact three-dimensional design, construction, and decency area is relatively small, elegant luster bright space is increased proven choice grade. So environmental automatic gas boiler excellent quality, the use of safe design makes installation and ongoing maintenance time-saving, higher import gas boiler burners make thermal efficiency, high degree of automation can save energy to protect the environment, structure and characteristics of their products a lot of advantages , so the gas boiler can provide high-quality water to meet the actual needs of customers at any time.

Beijing New Energy Automobile Co., Ltd. is China's first to operate independently and gain new energy automobile production qualification of new energy auto companies, mainly engaged in new energy vehicles and key parts and components research and development, production, sales and service business segments, and the layout intelligent manufacturing, energy management, smart travel, Internet +, and other strategic emerging industries. In the new energy automobile manufacturing process, and a series of paint drying processes can not do without the help of hot water mapna boiler engineering and manufact. Due to the company before the device has reached less than the growing production needs, the introduction of the 2017 mid-tail electric company producing heating pressure hot water boiler (CEDR0.7--95 / 70-Ⅱ).