The use of central heating industrial hot water boilers with diesel injector is the best choice for winter heating in northern China. Shanxi Province is located in Chang Darrow Heating Co., Ltd. mainly provides heating and post-service maintenance of heating equipment, heating clients involved in enterprises and institutions, office buildings, residential housing and a variety of commercial and other entertainment venues. With the wide blue sky covered Battle of the project, China's gradual increase in the proportion of heating for cleaning, heating, Ltd. Dalong Chang respond positively to the call of national policy, high pollution intensity wishing previously used, low thermal efficiency of coal-fired boiler to replace the traditional use hot water boiler clean fuel. After comparing many boiler manufacturers, choosing the optimal selection, determined and professional cooperation parties do fast boiler fuel boiler cleaning equipment. Providing a fast side 35 MW gas tube hot water boiler (SZS35-1.6-Y.Q) according to their actual needs.

Gas-fired steam boiler how to do proper maintenance during outage? Gas-fired steam boiler is the preferred industries of food processing, paper making, brewing, chemical production, now on the market boiler, gas steam boiler technology is very advanced, stable and sewage has run less obvious advantages of energy saving, but if it is long-term use, you should use the correct maintenance methods, in order to maintain the normal operation of the subsequent start.

Hot water boiler industrial hot water boilers with diesel injector normal operation and management of the normal operation and management of the boiler running to do: strengthen the monitoring of each operation of equipment and instruments, to maintain full water running, combustion stability, pressure stability. 1, boiler feed water and boiler water required to extend the service life, fuel economy, to ensure the quality of steam, to prevent scale boilers to cause slag corrosion damage and accidents member, using the unit shall GB / T1576-2008 "industrial boiler water" in provisions, the selected water treatment and oxygen equipment based on water quality and production requirements in the region, did not take reliable water treatment measures, the boiler must not be used. 2, fireman must be familiar with and master the position and role of various equipment and valves, boiler water circulation system. 3, should always observe the hot water boiler water temperature and pressure parameters to ensure stable pressure and water temperature, the outlet water temperature alarm should be fitted with devices to prevent the outlet water temperature is too high, resulting in boiling water hammer phenomenon, should always put the steam valve Deflation. 4, before the boiler circulation pump to start, and then renewed furnace, boiler in operation and just a cease-fire, non-stop operation of the circulating pump, in order to avoid water hammer caused by steam. 5, the boiler needs a short shutdown, the shutdown may not immediately stop the circulation pump only when the network feed water temperature drops below 40 ℃ only allowed to stop circulating pump. When put into operation again, it should start circulating pump. 6, the circulation pump is one of the main heating system of the device should be a preparation of a use. 7, always pay attention to changes in pressure, the pressure to keep the pot stable as possible, without rendering the pressure exceeds the maximum allowable working pressure. Pressure gauge elbow should be washed once per shift, in order to maintain the accuracy of pressure gauges, should be checked every year, such as reading a difference of 0.1MPa, should be repaired or replaced. 8, boiler import and export shall be equipped with electric contact pressure thermometer to reliably control the temperature, especially water temperature shall not exceed the specified boiler water temperature specification. Pressure gauge and a thermometer mounted at one side of the boiler should be concentrated. In order to observe and monitor.

75 tons circulating fluidized bed boiler has a power station boilers, steam boilers and industrial hot water boilers with diesel injectors, is ZG developed the fourth generation of a circulating fluidized bed boiler. 75 tons circulating fluidized bed boiler combustion chamber and vortex separator composed by the membrane wall, vortex separator located in the upper chamber, the left side of the furnace arrangement loopback device. All the furnace flue gas velocity is less than the terminal velocity of the upward movement of small particles with the flue gas, into the cyclone, more than cutting down the size of the particles are separated, forming a seal material in the feed back channel, and then sent back by the membrane porous semi-artesian device to the furnace material is mixed with hot bed combustion cycle repeated.