Due to the special nature of the industrial park location, we are more to consider whether the boiler with green features in the choice of boiler equipment. According to our survey of the entire boiler industry, quick side has considerable experience in research and development in the field of environmental cleaning boilers, boiler equipment while also providing low pollutant emissions for Beijing more enterprises and institutions, we are fully confident that the fast boiler ability. --customer feedback

Free supervisory inspection principles and characteristics of small 94 percent heating efficiency 2 ton steam boilers as the country increasingly stringent security checks on special equipment, many users are in for acceptance steam boiler to worry about, then there a boiler inspection and acceptance does not require it? The answer is yes, this is the free acceptance boiler steam boiler, supervisory inspector now free to receive more and more small steam boiler users of all ages, so check the small steam boiler-free monitoring What are the principles and characteristics of it? Then we explain for everyone. First small steam boiler uses a very broad, such as industry, food processing, school canteens, washing rooms, hospital disinfection, hotels, district heating, etc., there are coal, oil and gas heating, where coal-fired steam boilers currently in my company alone this one domestic production, steam boilers do not build a separate boiler room, small size, light weight, easy to move, can be placed in the basement, roof, etc., the Boilermakers do not need to operate licensed fireman, replacing every year dealing with government departments, small steam boiler-free acceptance than conventional boiler safety, this boiler will not explode, it is composed of a coil, burning very fast start, whether it is coal, oil or gas to ensure 3 minutes to a steam, does not require inspection and monitoring of the subject. Overpressure, over-temperature combustion, water and other multiple protection, ultra-safe, non-explosive, can greatly reduce the burden on the user.

Gas boiler precautions required during installation methods, or steps :( a) a foundation base of the boiler should be provided is determined according to the local soil, manufacturers design reference by the civil sector again. After reaching the base strength boiler, the boiler should drawings inspection and acceptance, and to draw the whole boiler three reference lines: a, longitudinal reference line - drum center or the center of the combustion apparatus. b, lateral reference line - the center of the front axle or chain grate slag centerline of the machine. C, elevation reference line - can be selected from a number of locations about four weeks, respectively, on the basis of the marking, the relative offset between the markers should not exceed 1mm. Furnace in place. After assembly the lower part of the boiler in place first, then the upper assembly large, the upper and lower portions need to find a combination of two positive pads firmly, should be both inside and outside the two casting. Installation location and size deviation test methods according to GB50273 "boiler installation engineering construction and acceptance" implementation. (B) lifting the boiler, during lifting, should be suspended on a lifting lug drum boiler ready large, the boiler on a foundation base coincides with the pre-drawn reference line. The longitudinal centerline of the boiler and the foundation, the deviation is not more than 3 mm, and the inclination with the center line of the drum hammer correction, allowing the central drum inclination is not larger than 5 mm, otherwise use horns foundation base and the junction pad level. Maximum level (c) Installation of boiler network (1), water supply conduit installation requirements typically require as backup pool below the normal water level line of the boiler, so as not to shutdown, boiler feedwater flowing into a large number of drainage caused to start the next . At the outlet of the tank (i.e., an inlet feed line) should be installed wire screen. (2), a main steam line installation requires the main steam lead pipe straight run section should be more than 0.5 m, the bending radius should be 4-5 times the diameter of the pipe, the trap should be fitted at the lowest line in order to prevent water hammer pipe, while to be reliable insulation. (3), the safety valve should be installed in the valve installation requirements after the hydrostatic test, the safety valve shall be fitted exhaust pipe, the exhaust pipe of the safety guide outside the boiler house, allowed valving the exhaust pipe. (4), mounting a lower water table level table downcomer must access a safe place, Hancock rotating flexible water table, not leaking, water table must be installed to the lighting device, easy to observe. (5), a pressure gauge mounting means so that when the scale gauge vertical plates, should be painted red gauge scale to show the maximum allowable pressure boiler, rotating flexible plug gauge, not leaking, water flow, pressure gauges insulation prohibited. (Iv) the boiler chimney installation requirements, when lifting the chimney, the chimney should be straight, horizontal direction lead length should not be too long, generally less than 5 meters, the height of the chimney should comply with relevant national standards. To add chimney rain cap, the weight of the chimney should not fall directly on the boiler chimney take over the host. Installation (e) combustion system: 1, according to the combustion system of FIG power line control circuit, a control signal line and the control line is electrically connected, the program should be installed reliable ignition and flame failure protection devices. Combustion process controller provides a separate set of contact start-stop control. May be formulated in a variety of burner start-stop loop cascade control relay 10A is a fuse, relay start-stop control stops the control terminal may be connected to the burner, may directly control the power of the burner. Both constant pressure sensor, water power, fuel, gas pressure set value is detected after the automatic controller opens. Time pressure sensor, water supply, oil, gas, and their detection circuit, alarm and found the problem immediately shutdown flame protection, the controller automatically displays the point of failure, an alarm sounds machine.

Oil and gas boilers for food factories

In all parts of the world, the most important thing is the food processing factory. Various food processing factories are covered by various large and small enterprises such as biscuit factories, meat processing factories and dairy factories. For these food processing plants, boiler applications are essential, and steam boiler applications are the most common. The food factory steam boiler is mainly used in the process of distillation, extraction, disinfection, drying and maturation in the food processing process, and the high temperature steam is used for high temperature cooking, drying and disinfection of the food. Of course, other boilers, such as some food plants, will sometimes be equipped with self-contained power station boilers for internal power generation, or hot water boilers for central heating of their plants, office buildings, and dormitory buildings. Of course, some processes in food factories require special processing of food by hot water boilers.